
BLUETTI EB3A Review (2026): 600W, Discontinued, Worth It Used?
Table of Contents
Affiliate disclosure: Some links on this page are affiliate links, including links to Amazon, EcoFlow and BLUETTI. If you buy through them we may earn a commission, at no extra cost to you. As an Amazon Associate we earn from qualifying purchases. This never influences our rankings or verdicts.
The BLUETTI EB3A is a 268.8Wh LiFePO4 power station with 600W of AC output (1,200W surge), 350W Turbo wall charging and 200W of solar input in a 10.1 lb box. BLUETTI has discontinued it: its US store lists every EB3A bundle as sold out, the bare unit last at $219. For a new unit, buy the Elite 30 V2 ($299.99 at BLUETTI); buy a used EB3A only under about $130.
How we evaluated it: Our verdict is based on BLUETTI's EB3A product page, spec table and FAQ, the EB3A user manual, BLUETTI's warranty policy and discontinued-models page, BLUETTI store and Amazon prices read on November 18, 2026, StorageReview's hands-on review (September 2022), and the runtime arithmetic shown below.
BLUETTI Elite 30 V2Buy at BLUETTICheck price on Amazon
BLUETTI EB3A review: quick verdict
The EB3A put a 600W inverter and LiFePO4 cells in 10.1 lb, listed at $299 on Amazon when StorageReview reviewed it in 2022, and it still covers a small kit well: two AC outlets, 100W USB-C, a 15W wireless pad, a car outlet and two 5.5mm barrel ports, with the charger built in, so it takes a plain AC cable and no brick. Four things date it. Its battery is rated for 2,500 cycles, against 3,000+ on the Elite 30 V2. Its UPS mode has no published switchover time, where the Elite 30 V2 is rated at 10 ms or less. Turbo charging is switched on in an app that connects over Bluetooth only. And the warranty was 24 months, so most units are already out of it. StorageReview also saw it stop charging at 95 to 96% with an overheat warning. For a new purchase, buy the Elite 30 V2. Buy a used EB3A only if it is cheap and comes with its AC and solar cables.
Is the BLUETTI EB3A discontinued?
Yes. On November 18, 2026 BLUETTI's US store titled the page "(Discontinued) BLUETTI EB3A Portable Power Station" and listed all three versions as sold out: the bare unit at $219, the kit with a 100W panel at $399 and the kit with 200W of solar at $618. Its 300W sibling, the AC2A ($149), carries the same label. BLUETTI's separate end-of-sale list does not name the EB3A or a successor (it pairs the AC60 with the AC240 and the EB70S with the AC70), so the replacement picks below are ours: the Elite 30 V2 is BLUETTI's current station with the same 600W rating and 7% more capacity. A search of Amazon US the same day found BLUETTI's newer stations and EB3A cables from other sellers, but no EB3A for sale.
BLUETTI says it still services discontinued models under warranty and sells their accessories while stock lasts. On November 18 its store still had the EB3A car charging cable and the MC4-to-DC7909 solar cable at $19.90 each. Our discontinued power station guide covers other end-of-sale models from BLUETTI, EcoFlow, Jackery and Anker.
BLUETTI EB3A specs
| Spec | Value (BLUETTI rating) |
|---|---|
| Capacity | 268.8Wh LiFePO4 (12Ah) |
| Cycle life | 2,500+ cycles to 80% of original capacity |
| AC output | 2 x 120V/5A outlets, 600W total, pure sine wave; 1,200W surge |
| Power Lifting | A mode in the BLUETTI app for heating loads such as space heaters and irons; BLUETTI's EB3A spec table gives it no wattage |
| USB and wireless | 1 x USB-C (100W), 2 x USB-A (5V/3A), 1 x 15W wireless pad |
| 12V DC | 1 x 12V/10A car outlet, 2 x 12V/10A DC5521 ports, all regulated |
| Total outputs | 9 |
| Wall charging | Built-in charger: 268W standard (full in 1.5 to 2 hours) or 350W Turbo, set in the app (1.3 to 1.8 hours) |
| Solar input | 200W max, 12 to 28V open-circuit, 8.5A: 1.8 to 2 hours in ideal sun |
| Wall plus solar | 430W max: 1.2 to 1.7 hours |
| Car charging | 100W from a 12V socket (3.2 to 3.7 hours) or 200W from 24V (1.9 to 2.4 hours) |
| UPS | UPS bypass mode, up to 600W; no switchover time published |
| Expansion | None (BLUETTI's FAQ: B230 and B300 batteries do not fit) |
| App | BLUETTI app over Bluetooth only |
| Weight and size | 10.14 lb (4.6 kg); 10.04 x 7.09 x 7.20 in |
| Temperature | Charge 32 to 104°F; discharge -4 to 104°F; storage 14 to 113°F |
| Certification | UL 2743, FCC and others |
| Warranty | 24 months |
Source: BLUETTI's US EB3A page and its user manual. The box held the EB3A, a 71-inch AC charging cable, a 59-inch MC4-to-DC7909 solar cable and the manual; the car charging cable was sold separately. BLUETTI's page headlines "80% charge in 30 minutes", which needs the full 430W of wall and solar together: 80% of 268.8Wh is 215Wh, and 215Wh at 430W is 30 minutes. From the wall alone, plan on 1.3 to 2 hours for a full charge.
What the EB3A runs, and for how long
The formula: runtime (hours) = 268.8Wh x 0.81 / average load (W). BLUETTI's own FAQ uses 90% depth of discharge times 90% inverter efficiency, which is 0.81, and StorageReview got 0.22kWh out of its unit on a 300W load, 82.1% of the rating. That leaves about 218Wh of AC energy, a little less than the 0.85 factor in our other reviews. Draws come from our appliance power guide; fridges use ENERGY STAR's median daily energy, since their compressors cycle.
| Load | Average draw | EB3A runtime |
|---|---|---|
| Wi-Fi router and modem | 20W | About 11 hours |
| CPAP, no heated humidifier | 20W | About 11 hours |
| CPAP with heated humidifier | 55W | About 4 hours |
| Laptop (MacBook Air 15-inch) | About 70Wh a charge | About 3 full charges |
| Four LED bulbs (60W equivalent) | 40W | About 5.4 hours |
| 32-inch TV | 31W | About 7 hours |
| 55-inch TV | 97W | About 2.2 hours |
| Box fan (20-inch), high to low | 83 to 56W | About 2.6 to 3.9 hours |
| Starlink (Standard kit) | 75 to 100W | About 2.2 to 2.9 hours |
| Mini fridge | 680Wh a day | About 7.7 hours |
| Full-size fridge | 1,500Wh a day | About 3.5 hours, if it starts |
| Blender | 400W (850W to start) | About 30 minutes of blending |
| Coffee maker, kettle or microwave | 900 to 1,500W | Over the 600W rating |
Start-up loads are the catch. A full-size fridge needs about 1,200W to start, which is the EB3A's entire surge rating, so some will trip it, and it would only carry one for about three and a half hours anyway. A mini fridge's 600W start fits easily. A 12V fridge-freezer such as Dometic's CFX3 45 (about 216Wh a day) runs from the 12V car outlet with no inverter loss, which stretches the EB3A to about a day. Power Lifting lets resistive heaters run at reduced heat, but a 1,500W space heater would empty the battery in minutes; it is not a heating tool.
CPAP users: one night, without the humidifier. At 20W the EB3A covers about 11 hours, so a full night; with a heated humidifier at about 55W it lasts about 4 hours. ECO mode turns the AC outlets off after four hours below 10W, which a CPAP at 20W stays above, but turn it off for overnight loads anyway. Our CPAP power station guide covers units that last two nights or more.
Charging from the wall, solar and a car
Wall charging is the EB3A's strong point for its age. The charger sits inside the case, so one AC cable does the job: 268W in standard mode, or 350W in Turbo, which you switch on in the app (the manual also lists a Silent mode). That puts a full charge at 1.3 to 2 hours. StorageReview found the app was the only way to change the charge rate, and its unit tripped an overheat warning at 95 to 96% when charging with no load, stopping with the fan off, cooling, then resuming. The reviewer suspected the firmware's fan profile and got no answer from BLUETTI.
Solar input is 200W at 12 to 28V and 8.5A. That 28V ceiling means most pairs of portable panels must be wired in parallel, not series. BLUETTI quotes about 2.7 hours with one PV120 panel and about 1.8 hours with one PV200. Wall and solar together reach 430W, as does a second AC source through BLUETTI's optional T200 adapter. In the car, the EB3A takes 100W from a 12V socket or 200W from a 24V truck socket.
Build, screen and app
At 10.14 lb and 10 x 7.1 x 7.2 inches, it is a one-hand carry. The wireless pad needs the DC output switched on; an LED lamp has its own button. BLUETTI's FAQ says to keep the unit upright, that it is not waterproof and that the battery cannot be replaced. An AC circuit breaker trips above 10A; press it to reset. StorageReview found the case light for its size and noted the app reports AC input differently from the unit's own screen.
The app connects over Bluetooth only, with no Wi-Fi, so your phone has to be close by. StorageReview's bigger worry was app dependence: if BLUETTI ever drops support for the EB3A in its app, Turbo and Silent charging go with it. The unit's buttons still handle power on and off, ECO mode and the AC frequency setting.
What we like
- A 600W pure sine wave inverter with 1,200W surge in a 10.1 lb box.
- A built-in charger: one plain AC cable, full in 1.3 to 2 hours.
- LiFePO4 cells rated for 2,500+ cycles to 80%.
- 100W USB-C, a 15W wireless pad and two 12V/10A barrel ports.
What we don't like
- No published UPS switchover time; the Elite 30 V2 is rated at 10 ms or less.
- A 2,500-cycle rating and a 24-month warranty, against 3,000+ cycles and 5 years on the Elite 30 V2.
- Turbo and Silent charging only through the Bluetooth app.
- Discontinued: no new units, and most units are past their warranty.
Buying a used EB3A: what to check
- The US model. BLUETTI made the EB3A in a 120V US version and a 220 to 240V version for Europe, the UK and Australia. Check the outlets and the label; BLUETTI's warranty only applies in the country of purchase.
- The original invoice. BLUETTI's warranty policy asks for proof of purchase showing the product, price and sales channel, and excludes units bought from unauthorized resellers. The warranty ran 24 months, so a unit bought before November 2024 is out of it.
- The cables. Make sure the AC charging cable and the MC4 solar cable come with it. BLUETTI still sold the car and solar cables at $19.90 each on November 18, 2026.
- A full charge. Charge it from low on Turbo and watch for the overheat stop StorageReview saw near 96%, or a reading that jumps.
- A real load. Run a load of 400W or more for a few minutes and check the outlets hold.
- The app. Pair it over Bluetooth before you pay; you need the app for Turbo charging.
On price, our line is about $130 with both cables. A new Elite 30 V2 costs $289.99 to $329.99 on Amazon depending on color and $299.99 at BLUETTI, with a 5-year warranty, 3,000+ cycles and a rated 10 ms UPS. A used EB3A has no warranty in most cases, an unknown cycle count and a lower rating, so it is worth under half the new price. Our guide to buying a used solar generator has the full checklist.
EB3A vs AC2A and Elite 30 V2
| EB3A | AC2A | Elite 30 V2 | |
|---|---|---|---|
| Capacity | 268.8Wh | 204Wh | 288Wh |
| AC output | 600W | 300W | 600W (1,500W Power Lifting) |
| Wall charging | 268W, 350W Turbo | 270W | 380W |
| Solar input | 200W | 200W | 200W |
| Cycle rating | 2,500+ | 3,000+ | 3,000+ |
| App | Bluetooth | Bluetooth | Wi-Fi and Bluetooth |
| Weight | 10.1 lb | 7.9 lb | 9.48 lb |
| Status, Nov 18, 2026 | Discontinued, sold out (last $219) | Discontinued, sold out (last $149) | In stock: $299.99 at BLUETTI, $289.99 to $329.99 on Amazon |
BLUETTI's comparison table on the EB3A page supplies the AC2A figures; the Elite 30 V2's come from our Elite 30 V2 review. Outside BLUETTI, the 600W EcoFlow RIVER 3 Plus is the closest rival, while the Jackery Explorer 300 and Anker SOLIX C300 are 300W units.
What to buy instead of the EB3A
| Pick | Capacity | Output | UPS | Weight | Price, Nov 18, 2026 |
|---|---|---|---|---|---|
| Elite 30 V2 (closest match) | 288Wh | 600W, 1,500W Power Lifting | 10 ms or less | 9.48 lb | $299.99 at BLUETTI; $289.99 to $329.99 on Amazon by color |
| Elite 100 V2 (a fridge or two CPAP nights) | 1,024Wh | 1,800W, 3,600W surge | 10 ms or less | About 25 lb | $499 at BLUETTI; $549 pre-order on Amazon |
| Elite 30 mini (lighter loads) | 288Wh | 300W, 600W Power Lifting | 10 ms or less | 7.3 lb | $239.99 at BLUETTI |
Elite 30 V2: the closest match
Same 600W output, 288Wh of capacity, 1,500W Power Lifting for heating loads, 380W wall charging (80% in about 45 minutes), a 10 ms UPS with up to 980W passing through from the wall, 140W and 100W USB-C, Wi-Fi as well as Bluetooth, 3,000+ cycles and a 5-year warranty, in 9.48 lb. It drops the wireless pad, and its two barrel ports are 12V/5A instead of 10A. For a router, CPAP or laptop, it does everything the EB3A did, with a rated switchover.
BLUETTI Elite 30 V2Buy at BLUETTICheck price on Amazon
Elite 100 V2: for a fridge or two nights of CPAP
If the EB3A ran out too soon, the Elite 100 V2 is the step up: 1,024Wh, 1,800W with 3,600W surge, 1,000W of solar and 1,200W Turbo wall charging, at about 25 lb. With about 870Wh usable, it runs a CPAP with a heated humidifier for about 16 hours, two nights, and starts and carries a full-size fridge for about 14 hours.
BLUETTI Elite 100 V2Buy at BLUETTICheck price on Amazon
Elite 30 mini: for lighter loads
BLUETTI's newest small unit puts 288Wh in 7.3 lb, with a built-in retractable 140W USB-C cable, a 10 ms UPS and BLUETTI's 3,000+ cycle rating to 80%. Its AC side is rated at 300W (600W Power Lifting), half the EB3A's, so it suits laptops, phones, a router and a CPAP without humidifier, not a blender. Buy it from BLUETTI: Amazon's listings were $449 to $459 on November 18, 2026.
BLUETTI Elite 30 miniBuy at BLUETTI
Who should buy the BLUETTI EB3A
Buy a used one for phones, laptops, a router or a CPAP without humidifier on a camping weekend, if it is the US model, cheap, and comes with its cables. Skip it if you want rated switchover backup for a computer or CPAP, a full-size fridge, or a warranty; for those, see the picks above, our BLUETTI lineup guide or our best power stations under $500.
Final verdict
The EB3A was a good small LiFePO4 station: 600W, a built-in fast charger and 10.1 lb. In late 2026 it is a used-market unit with an unrated UPS, a Bluetooth-only app and, in most cases, no warranty. For a new BLUETTI in the same class, buy the Elite 30 V2.
BLUETTI Elite 30 V2Buy at BLUETTICheck price on Amazon
Frequently Asked Questions
Is the BLUETTI EB3A discontinued?
Yes. On November 18, 2026 BLUETTI's US store titled the EB3A page "(Discontinued)" and listed all three versions as sold out, the bare unit last at $219. BLUETTI says it still provides warranty service for discontinued models and sells their accessories while stock lasts.
What replaced the BLUETTI EB3A?
BLUETTI has not named a successor, but its closest current model is the Elite 30 V2: 288Wh, 600W of output, 380W wall charging, a 10 ms UPS, 3,000+ cycles and a 5-year warranty, for $299.99 at BLUETTI. For lighter loads, the 300W Elite 30 mini is $239.99.
How long will a BLUETTI EB3A run a CPAP?
About 11 hours for a CPAP drawing 20W without a heated humidifier, using about 218Wh of usable energy (BLUETTI's 90% depth of discharge times 90% inverter efficiency). With a heated humidifier at about 55W it lasts about 4 hours, less than a full night.
Can a BLUETTI EB3A run a refrigerator?
A mini fridge, yes: about 7.7 hours at ENERGY STAR's median of 680Wh a day, and its 600W start fits. A full-size fridge needs about 1,200W to start, the EB3A's whole surge rating, and would run only about 3.5 hours if it starts.
Does the BLUETTI EB3A work as a UPS?
It has a UPS bypass mode: with wall power connected and the AC output on, grid power feeds the outlets (up to 600W) and charges the battery. BLUETTI publishes no switchover time, so it is not a rated UPS for a desktop computer. The Elite 30 V2 is rated at 10 ms or less.
How long does the BLUETTI EB3A take to charge?
About 1.5 to 2 hours on the standard 268W wall charger, 1.3 to 1.8 hours in the app's 350W Turbo mode, 1.8 to 2 hours on 200W of solar in ideal sun, and 1.2 to 1.7 hours with wall and solar together at 430W.
Is a used BLUETTI EB3A worth buying?
Only cheap. A new Elite 30 V2 costs $289.99 to $329.99 with a 5-year warranty, so we would cap a used EB3A at about $130 with its AC and solar cables. Make sure it is the 120V US model and ask for the original invoice.


